ZD47多工位自動冷鐓機
|
 
|
|
ZD47多工位自動冷鐓機采用張閉式夾鉗傳送工件，每把夾鉗張閉時間可單獨調整；采用整圓套筒切刀，切口平整。主要動作機構（切斷，凹模推出，送料等）的傳動采用連桿形式；滿足大盤圓送料6帶搓絲機構，實現螺栓，螺釘從切斷，鐓鍛至搓絲一條線自動化生產；第三工位的凹模推出適用于切邊工藝或鐓鍛工藝，變換調整方便；每個工位均有沖頭推出機構，并可分為單獨調整；具有氣動控制的離合器和制動器，使主電機在無負荷下啟動，寸動靈活，調試機床時方便，停機時主滑塊自動停止后止點。
┏━━━━━━━━━━━━━━━━━━━━━┳━━━━━┳━━━━━━┓
┃ ┃ ┃ ┃
┣━━━━━━━━━━━━━━━━━━━━━╋━━━━━╋━━━━━━┫
┃鐓鍛工位數Median heading blacksmith ┃ 個A ┃ 4 ┃
┣━━━━━━━━━━━━━━━━━━━━━╋━━━━━╋━━━━━━┫
┃ 額定鐓鍛力Rated upsetting force ┃ KN ┃ 1200 ┃
┣━━━━━━━━━━━━━━━━━━━━━╋━━━━━╋━━━━━━┫
┃最大切斷直徑Maximum cutting diameter ┃ mm ┃ 14 ┃
┣━━━━━━━━━━━━━━━━━━━━━╋━━━━━╋━━━━━━┫
┃ 最大切斷長度Maximum cutting length ┃ mm ┃ 150 ┃
┣━━━━━━━━━━━━━━━━━━━━━╋━━━━━╋━━━━━━┫
┃制件桿部最大直徑Shank diameter parts ┃ mm ┃ 12 ┃
┣━━━━━━━━━━━━━━━━━━━━━╋━━━━━╋━━━━━━┫
┃制件桿部長度Minister degrees rod parts ┃ mm ┃ 20-120 ┃
┣━━━━━━━━━━━━━━━━━━━━━╋━━━━━╋━━━━━━┫
┃ 最大螺紋長度Maximum thread length ┃ mm ┃ 45 ┃
┣━━━━━━━━━━━━━━━━━━━━━╋━━━━━╋━━━━━━┫
┃ 四模最大推出長度 ┃ mm ┃ 125 ┃
┃ Maximum length of the die launched ┃ ┃ ┃
┣━━━━━━━━━━━━━━━━━━━━━╋━━━━━╋━━━━━━┫
┃ 沖頭最大推出長度 ┃ ┃ ┃
┃ Maximum length of the punch launched ┃ mm ┃ 25 ┃
┣━━━━━━━━━━━━━━━━━━━━━╋━━━━━╋━━━━━━┫
┃ 鐓鍛工位距 ┃ ┃ ┃
┃ Heading away from the blacksmith bit ┃ mm ┃ 1 10 ┃
┣━━━━━━━━━━━━━━━━━━━━━╋━━━━━╋━━━━━━┫
┃ 凹模子L直徑Die diameter ┃ mm ┃ 80 ┃
┣━━━━━━━━━━━━━━━━━━━━━╋━━━━━╋━━━━━━┫
┃ 沖頭子L直徑Punch diameter ┃ mm ┃ 60 ┃
┣━━━━━━━━━━━━━━━━━━━━━╋━━━━━╋━━━━━━┫
┃ 主電機功率Main motor power ┃ mm ┃ 22 ┃
┣━━━━━━━━━━━━━━━━━━━━━╋━━━━━╋━━━━━━┫
┃ 生產率Productivity ┃ pcs/min ┃ 100-120 ┃
┣━━━━━━━━━━━━━━━━━━━━━╋━━━━━╋━━━━━━┫
┃ 機器重量Weight ┃ kg ┃ 23000 ┃
┗━━━━━━━━━━━━━━━━━━━━━┻━━━━━┻━━━━━━┛
以上數據僅供參考之用，本公司隨時進行技術改進、因此保有隨時更改設計規格之權利
ZD47 multi-station automatic cold header sent by Chang closed clamp the workpiece;each of the clamp closed time sheets can be individually adjusted; sleeve with full roundcutter, cut flat, Major Action Agency (cut, die introduction of feed, etc.)drive by connectingrod form; meet with the broader market round feeding 6 Roll institutions, to achieve bolts,screws from the cutting, upsetting to a line of automated production thread rolling; the thirdwork Introduction die bit for trimming process or upsetting process, transform easyadjustment; punch each station has launched organizations, and separately adjusted, withpneumatic control of the clutch and brake, so that the main motor at no load Start, inchingflexible, convenient when debugging tools, stop automatically when the slide stop after themain point only. |
|
注：聯系我時，請說是在“傲立機床網”上看到的，謝謝！
添加為商業伙伴
